Hi Fernandez , Thanks for responding so promptly, can you please do me one more favor and pass me the details of someone in cyntech, i went to the website and it had so many contacts in different countries i dropped email to couple of them but did not get any response
↧
Forum Post: RE: PMP22650: PMP22650: VT-20163 Transformer and VI-20174A PFC coupled inductor
↧
Forum Post: RE: TIDA-00254: Connects to Computer Webcam Instead of OpenCV Camera
Hello Josel, The team will need some time to look into this issue further. Thanks, Alex Chan
↧
↧
Forum Post: RE: PSPICE-FOR-TI: What is the process to migrate my Pspice for TI license to a new computer?
I'll have to have the old install disabled. Are there computers that you want to keep this active, or can I disable all installations? If you want to keep any, please provide me with the name of the machines that you want to keep PSpice for TI installed on. Regards, David
↧
Forum Post: RE: TIDA-010076: For 100BASE-T1 PoDL class 0~15
Hi Steffen and Henry, Based on your schematic, it seems like you are using " RGMII (TX and RX Internal Delay Mode)". If the MAC side does not have any internal shift or delay between clock and data. This strapping is good for RGMII interface. -- Regards, Hillman Lin
↧
Forum Post: RE: PSPICE-FOR-TI: What is the process to migrate my Pspice for TI license to a new computer?
Thank you David Could you disable all three of my installations? And then, I'd like to reinstall PSpice on my computer.
↧
↧
Forum Post: RE: PMP41009: UCC28740-Q1
Hi Shilin, What's the output voltage and output current for your design? What's the output current and voltage for the waveform?
↧
Forum Post: RE: PMP41009: UCC28740-Q1
Hi Linda, CH1 is the output1(about 15V\0.3A)，CH2 is the output 2(about 12V\0.125A)
↧
Forum Post: PSPICE-FOR-TI: Netlist error
Part Number: PSPICE-FOR-TI Tool/software: It is showing netlist error for any schematic drawn. Please solve this issue.
↧
Forum Post: RE: TIDA-050047: Query Battery / charging /discharging information from TPS25750 connected to host
Hassan, Have you looked into https://www.ti.com/lit/ta/sszt229/sszt229.pdf?ts=1719896675689&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FTPS25750 Also, please note you must be connected to the I2C master interface.
↧
↧
Forum Post: RE: LM25149-Q1: simulation not enabled for this design
Thanks for your response, Here are simulated details: 1. Vin range :18 V to 25 V 2. Vout : 5 V +- 1% 3. Iout: 8 A +- 1% 4. Fsw : Recommended operating frequency I want to know the how the this will behave at this conditions and also comparison results between with input filter and without input filter. Is LM25148-Q1 without filter results is same as LM25149-Q1 with filter ? Thanks & Regards, B Malakondareddy.
↧
Forum Post: PMP4408: SMPS FLYBACK
Part Number: PMP4408 Tool/software: Hi sir, We need to design an SMPS Flyback topology with the following specifications: Input Voltage: MAX 275VAC Output 1: 12V 5A Output 2: 5V 5A Please recommend a suitable transformer and control IC for this design.
↧
Forum Post: RE: TIDA-050047: Query Battery / charging /discharging information from TPS25750 connected to host
Hi Deepak! Thank you for the reply. This document is new to me. However, my question remains unresolved. I understand the TPS can act as an i2c host for the BQ charger as the document states. but my question remains. How can I get battery information in such a case directly from the BQ? I have two options on my pcb, both the integrated and non-integrated options from the document. currently I am using non-integrated option. If I switch to the integrated option, are my i2c reads (intended for BQ charger) supposed to be directed to the i2c address of the TPS and it will automatically get the necessary data from the BQ charger and reply?
↧
Forum Post: PSPICE-FOR-TI: PSPICE-FOR-TI
Part Number: PSPICE-FOR-TI Tool/software: When I'm trying to reinstall Pspice it showing that Ive reached concurrent access limit.
↧
↧
Forum Post: RE: LM27761: Why no tool?
Hi Richard, Unfortunately the designs of our older parts like LM27761 are not implemented in WEBENCH. I will feedback the info to remove that statement in the datasheet. Best regards, Varun
↧
Forum Post: RE: TIDA-01487: TIDA-01487 communication issue
Hi Maggie, Thank you for your question. At which CAN speed does the issue occur? Can the customer test a lower CAN speed overall, to see if the principal arbitration logic is working correctly? Overall I saw in the schematic the use of LV devices. We use in TIDA-01487 LVC devices, which have a low propagation delay. I think low propagation delay of the arbitration circuit is needed to achieve high CAN speed. Regards, Thomas
↧
Forum Post: RE: CODECOMPOSER: CCS Headless build fails because of missing Compiler installation
Hello, I am still waiting for the solution. Compared to the Classification "TI Thinks Resolved", this problem still exists. We have a product resp. prototype with the TI AM64, and we need this headless build approach to implement our software provision for the subcores of the AM64. This is a very disappointing situation.
↧
Forum Post: RE: PMP23338: PMP23338 CCS
Hello, Thanks for the suggestion. I have another query regarding the Boost Inductor Design. The procurement of inductor from Pulse is in process and taking some time. Meanwhile, after referring to the Boost Inductor Design section(2.3.1) of the PMP23338 Test Report(TIDT369A) suggests winding 44turns on a single core of C058894A2HTto get 240uH of no load inductance. However the calculations and actually winding the single C058894A2HT core with 44 turns is not giving the same results. Can you clarify how 240uH no load inductance is achieved with it? Regards,
↧
↧
Forum Post: TIDA-010938: TIDA-010938
Part Number: TIDA-010938 Tool/software: Hello, Can I have that firmware for TIDA-010938? Thank you Lan
↧
Forum Post: LAUNCHXL-F28P65X: Control Card F28P65X
Part Number: LAUNCHXL-F28P65X Other Parts Discussed in Thread: C2000WARE Tool/software: Hi Good Morning Everyone, I am using specific board "Control Card F28P65X". I am trying to understand the sample example projects from solving some specific questions based on EPWM-Examples. I tried to debug and run some sample projects related to EPWM. It's generating the error. Mainly, I imported the project to analyze the behavior of PWM module pulse. It's not generating any specific "out" file. Can anyone tell me what can be best solution to debug or execute this example projects. I await for your answer. Thank you Error Type : 1) "C28xx_CPU1: GEL: Encountered a problem loading file: C:\C2000Ware\C2000Ware_5_02_00_00\driverlib\f28p65x\examples\c28x\epwm\CCS\epwm_ex2_updown_aq\CPU1_FLASH\epwm_ex2_updown_aq.out Could not open file" 2) gmake: *** [build-1222142495] Error 1 3) Description Resource Path Location Type gmake: Target 'all' not remade because of errors. epwm_ex2_updown_aq C/C++ Problem
↧
Forum Post: RE: TIDA-050047: Query Battery / charging /discharging information from TPS25750 connected to host
Hassan, The PDdevice can control BQ charger over I2Cm lines. Initialization, change in voltage and current settings are done over I2Cm lines. If the an external controller need to know some data from BQcharger, the external controller can use the I2Cw and I2Cr 4CC commands.
↧