Forum Post: RE: Debugging multiple targets via Blackhawk USB2000
[quote user="Johan W���lger"]I am using Blackhawk USB 2000 emulators. Do you need any more information about them such as revision or serial number? Any hint where that can be found if that is the...
View ArticleForum Post: RE: Compiler Errors not reset upon successful build?
I believe it might have something to do with the number of source files. Attached is a test case with 256 source files.- Clean and build- Change function name in in func000.c from func000() to...
View ArticleForum Post: RE: MSP GANG DLL - Help is needed urgently
Hi Quote,Above two articles were posted by me when I was trying to understand how MSP-GANG DLL works, anyway, we still have problem to use the MS-GANG DLL in our VB6 test application. Can TI Team...
View ArticleForum Post: MSP430F5328 Memory Size in CCSv5
I use the Memory Allocation display in CCSv5 (using Version: 5.4.0.00091 ). It shows that the Flash size is 48000, but I thought the flash size I should have available is 128KB. I do have MSPF5328...
View ArticleClik here to view.
Forum Post: RE: BUILD PROJECTS OMAP L134 LCDK XDS ERROR
Rob,Did you follow the exact procedure at the Getting Started guide (check here)? The project for the C674x GPIO LED builds fine for me:I am using CCSv5.5 and the same Starterware as you. Keep in mind...
View ArticleForum Post: ELF format with build path embedded into binary file after...
Code Composer 5.1.00x:When I build a binary file ( *.b0) from the generated ELF-formatted file using hex6x, I notice the build path is put in the binary. This is bad because the CRC is calculated over...
View ArticleForum Post: RE: TivaWare USB Mouse Example
Thanks for the input. I did actually already make such a post there, and users in that forum told me to post in this one!
View ArticleForum Post: RE: Zoom OmapL138 audio programming help
Hi Mike,I would check out Zoom's support page for the L138. There are a lot of documents and example software for it to help you get started.Thankski
View ArticleForum Post: RE: Data verification failed at address 0xC3100000. Please verify...
Hello Melanie,[quote user="MELANIE JARNOUX"]Data verification failed at address 0xC3100000. Please verify target memory and memory map[/quote]The primary causes of this error is documented...
View ArticleForum Post: RE: TivaWare USB Mouse Example
Hi Christopher,are you looking for an example or to overcome a ccs error?If you are looking to overcome an error, this is the right forum and any details would help.If you are looking for an example,...
View ArticleForum Post: RE: Need help with the watching of assembly variables in the...
[quote user="Sachin Madhusoodhanan"]I need help with the watching of assembly variables in the watch window[/quote]Do you have the variables defined as .global? I assume you already refered to this...
View ArticleForum Post: RE: TMS320F28335
Hi,I would install control suite. Not only will you then have header files but also examples.Best Regards,Lisa
View ArticleForum Post: ELF format with build app_pe64Pe path embedded into binary file...
Code Composer Version: 5.1.0.09000When I build a binary file ( *.b0) from the generated ELF-formatted file using hex6x, I notice a build path is put in the binary. This is bad because the CRC is...
View ArticleForum Post: RE: Chronos 433 firmware
Hi Florian,ok, great to hear and thanks for the update.All the best with development.Best Regards,Lisa
View ArticleForum Post: RE: C55xx Malloc = 16-bit and heap = 8-bit??
...and (I know you're not the guy to bust on this but)...This (from the C5515 datasheet) is also confusing and somewhat misleading:320K Bytes Zero-Wait State On-Chip RAM,Composed of:– 64K Bytes of...
View ArticleForum Post: RE: Compiler Errors not reset upon successful build?
Perhaps the problem I observed got fixed in later versions of CCS. Not at my dev box. I think I am running CCS 5.1. I'll update CCS one day.
View ArticleForum Post: RE: Code Composer C-Programming structure auto populate
[quote user="alan alban"]In visual studio, for instance, I would put a dot (SysCtrlRegs.)and it would tell me the elements of that "structure" or whatever they call it here in a drop down. Is there a...
View ArticleForum Post: RE: MSP430F5328 Memory Size in CCSv5
Hi Max,yes. I hope that explains things.Best Regards,Lisa
View ArticleForum Post: RE: Getting "0BAD0BAD" data from CCS
Nabeel,Yes, usually this is the case. In the past this error used to be very common as this string was displayed in other scenarios as well (invalid or NULL memory, etc.). Nowadays most of these errors...
View Article