Forum Post: RE: How can i migrate project CCS version from 3.3 to 5.2?
Thanks for your reply Gautam.I've read the guide pdf linked from you but this document never show how migrate project CCS version from 3.3 to 5.2my question is how can I use "xdcpath.dat" and project...
View ArticleForum Post: RE: After installing, I get errors CCS 5.5.0.00077
Good to know that your issue's resolved!Happy Holidays!Gautam
View ArticleForum Post: RE: CCS5.5 Update problem
Dear all,I attached zip file again. (Please visit the site to view this file)Sincerely,Eui-heon
View ArticleForum Post: WEBENCH TO ORCAD 16.5 EXPORT PROBLEM
Hi,I design buck converters with TPS56121 and TPS40304 (input volt: 10-13 output volt: 8.5V and 25A) but when i tried to export into Orcad 16.5 there is a session warnings and erros. Some lines became...
View ArticleForum Post: RE: 'Run - Load - Verify program... ' How 'Verify Program...' can...
Hi again Malevi,When you go to Run -> Load -> Verify program (Option available only while debugging else it would be greyed out)It 'll ask you to verify the out file with the loaded one. If the...
View ArticleForum Post: RE: cdecls alternatives for linear assembly
Thanks George for confirming this.RegardsSudheesh
View ArticleForum Post: RE: c2000 compiler optimization problem
Thanks for the reply. Its a bit late to sort out the code and options because of the holiday --- we're shut down for a week -- so I'll have to get more detailed code to you in the New Year.The source...
View ArticleForum Post: RE: TINA-TI: transient simulation with swept parameter fails
Britt,Sure thing. I have attached a simple parameter sweep simulation based on the TPS61020 Transient Steady State Reference Design (http://www.ti.com/product/tps61020#toolssoftware).To reproduce the...
View ArticleForum Post: RE: error #10099-D: program will not fit into available memory
Ok, now it works. I had to delete the instruction TIMERA0_VECTOR from my vector table. I didn't know why there is this vector table, it was from a previous employee.
View ArticleForum Post: RE: C2000 v6.2.x C-compiler changed order of updates in 2 arrays...
Actually this file tuned out to be optimized by opt_level=2 (global optimization). The example source project is attached.Anyway old version (6.1.16) worked Ok. The updated union P_->pattern is used...
View ArticleForum Post: RE: Hex Conversion for Command File without SECTIONS Directive
Hi Archaeologist,Thank you for your reply. Sorry for my late reply.I understand that the ROMS Directive needs to roughly match the linker command file's MEMORY specification when the SECTIONS Directive...
View ArticleForum Post: RE: memory problem , msp430 , code composer v.5.4.
Thank you !I understand now
View ArticleForum Post: RE: CSSv5: stdout printf
thanks victoria,sometimes it could really be that easy! increasing the stack+heap-size worked for me!it is a bit strange, that not even an ordinary hello-world works with the standard configuration...
View ArticleForum Post: RE: 'Run - Load - Verify program... ' How 'Verify Program...' can...
[quote]Also, can I programming MSP430 without debugging? Just programme the flash is not enough for MSP430[/quote]Yes you can do it by using CCS Uniflash. Build your project -> Program your...
View ArticleClik here to view.
Forum Post: RE: Cannot Load image: "Does not match the target endianness"
Hi lyer, Thank you for your reply. I have my issue solved. I have reset the project and redo the same procedure again. This time, I could load the symbols into the DM8168. But I have another...
View ArticleForum Post: Grace - How to modify and apply a *.cfg
I´ve picked a blinking led project for the LaunchPad (G2231) and wanted to modify the blink frequency (division factor of the MCLK and SMCLK). I modified the divider in de led.cfg view but I don´t know...
View ArticleForum Post: FFT implementation using 'C54x
I test the program FFT who write in TMS320C54x DSP application guide by CCS2 but when i bluid the sumilator show a following error warning: entry point symbol _c_int00 undefinedundefined...
View ArticleForum Post: RE: install CCS V5 problem?
you can put the installation package on the C drive just like jung tae-hwa said
View ArticleForum Post: Reading a CPU load value
Good afternoon,Is there a way to read the CPU Load value so that I might print it out during the run time?Regards,John.---------------------------------CCS 5.4 EVMC6618 + USB XDS560v2 Mezzanine Emulator
View ArticleForum Post: Reading a CPU load value
Good afternoon,Is there a way to read the CPU Load value so that I might print it out during the run time?Regards,John.---------------------------------CCS 5.4 EVMC6618 + USB XDS560v2 Mezzanine Emulator
View Article